TTO on Dos box
TTO on Dos box
How to set it up i have installed the dosbox and i have dragged the tto folder on it end when i try to run it it sits at black screen and after some time starts to write an error mesege all over and over.
So why it doesn't work?
My pc is: 2000mhz celeron 128mb ram 40gb Hdd 32mb Nvidia geforce2 video card an Wind 2000 pro
Please help me becouse i want to run my tto again
So why it doesn't work?
My pc is: 2000mhz celeron 128mb ram 40gb Hdd 32mb Nvidia geforce2 video card an Wind 2000 pro
Please help me becouse i want to run my tto again
In order to protect the visitors of this site,
TTO Full Conversion!
This post has been lol 1337 times.
- spaceman-spiff
- Retired Moderator
- Posts: 20634
- Joined: 28 Jul 2002 07:08
- Location: Belgium
- Contact:
-
- Chief Executive
- Posts: 659
- Joined: 31 May 2004 08:22
try this config
[sdl]
# fullscreen -- Start dosbox directly in fullscreen.
# fulldouble -- Use double buffering in fullscreen.
# fullfixed -- Don't resize the screen when in fullscreen.
# fullwidth/height -- What resolution to use for fullscreen, use together with fullfixed.
# output -- What to use for output: surface,overlay,opengl,openglnb.
# hwscale -- Extra scaling of window if the output device supports hardware scaling.
# autolock -- Mouse will automatically lock, if you click on the screen.
# sensitiviy -- Mouse sensitivity.
# waitonerror -- Wait before closing the console if dosbox has an error.
fullscreen=true
fulldouble=false
fullfixed=false
fullwidth=0
fullheight=0
output=surface
hwscale=1.00
autolock=true
sensitivity=100
waitonerror=true
[dosbox]
# language -- Select another language file.
# memsize -- Amount of memory dosbox has in megabytes.
# machine -- The type of machine tries to emulate:hercules,cga,tandy,vga.
language=
machine=vga
memsize=16
[render]
# frameskip -- How many frames dosbox skips before drawing one.
# snapdir -- Directory where screenshots get saved.
# aspect -- Do aspect correction.
# scaler -- Scaler used to enlarge/enhance low resolution modes.
# Supported are none,normal2x,advmame2x,hq2x
# hq2x_threshold -- The threshold used to detect edges in hq2x
# Possible values are 4-128, can be modified with Ctrl+F3/F4
frameskip=0
snapdir=snaps
aspect=false
scaler=none
hq2x_threshold=18
[cpu]
# core -- CPU Core used in emulation: normal,full,dynamic.
# cycles -- Amount of instructions dosbox tries to emulate each millisecond.
# Setting this higher than your machine can handle is bad!
# cycleup -- Amount of cycles to increase/decrease with keycombo.
# cycledown Setting it lower than 100 will be a percentage.
core=dynamic
cycles=18000
cycleup=500
cycledown=500
[mixer]
# nosound -- Enable silent mode, sound is still emulated though.
# rate -- Mixer sample rate, setting any devices higher than this will
# probably lower their sound quality.
# blocksize -- Mixer block size, larger blocks might help sound stuttering
# but sound will also be more lagged.
# wavedir -- Directory where saved sound output goes when you use the
# sound record key-combination, check README file.
nosound=false
rate=22050
blocksize=2048
wavedir=waves
[midi]
# mpu401 -- Enable MPU-401 Emulation.
# device -- Device that will receive the MIDI data from MPU-401.
# This can be default,alsa,oss,win32,coreaudio,none.
# intelligent -- Operate in Intelligent mode.
# config -- Special configuration options for the device.
mpu401=true
intelligent=false
device=default
config=
[sblaster]
# type -- Type of sblaster to emulate:none,sb1,sb2,sbpro1,sbpro2,sb16.
# base,irq,dma,hdma -- The IO/IRQ/DMA/High DMA address of the soundblaster.
# mixer -- Allow the soundblaster mixer to modify the dosbox mixer.
# sbrate -- Sample rate of soundblaster emulation.
# oplmode -- Type of OPL emulation: auto,cms,opl2,dualopl2,opl3.
# On auto the mode is determined by sblaster type.
# oplrate -- Sample rate of OPL music emulation.
type=sb16
base=220
irq=7
dma=1
hdma=5
mixer=true
sbrate=22050
oplmode=auto
oplrate=22050
[gus]
# gus -- Enable the Gravis Ultrasound emulation.
# base,irq1,irq2,dma1,dma2 -- The IO/IRQ/DMA addresses of the
# Gravis Ultrasound. (Same IRQ's and DMA's are OK.)
# rate -- Sample rate of Ultrasound emulation.
# ultradir -- Path to Ultrasound directory. In this directory
# there should be a MIDI directory that contains
# the patch files for GUS playback. Patch sets used
# with Timidity should work fine.
gus=true
rate=22050
base=240
irq1=5
irq2=5
dma1=3
dma2=3
ultradir=C:\ULTRASND
[speaker]
# pcspeaker -- Enable PC-Speaker emulation.
# pcrate -- Sample rate of the PC-Speaker sound generation.
# tandy -- Enable Tandy 3-Voice emulation.
# tandyrate -- Sample rate of the Tandy 3-Voice generation.
# disney -- Enable Disney Sound Source emulation.
pcspeaker=true
pcrate=22050
tandy=true
tandyrate=22050
disney=true
[bios]
# Nothing to setup yet!
[dos]
# xms -- Enable XMS support.
# ems -- Enable EMS support.
xms=true
ems=true
[modem]
# modem -- Enable virtual modem emulation.
# comport -- COM Port modem is connected to.
# listenport -- TCP Port the momdem listens on for incoming connections.
modem=false
comport=2
listenport=23
[ipx]
# ipx -- Enable ipx over UDP/IP emulation.
ipx=true
[autoexec]
# Lines in this section will be run at startup
[sdl]
# fullscreen -- Start dosbox directly in fullscreen.
# fulldouble -- Use double buffering in fullscreen.
# fullfixed -- Don't resize the screen when in fullscreen.
# fullwidth/height -- What resolution to use for fullscreen, use together with fullfixed.
# output -- What to use for output: surface,overlay,opengl,openglnb.
# hwscale -- Extra scaling of window if the output device supports hardware scaling.
# autolock -- Mouse will automatically lock, if you click on the screen.
# sensitiviy -- Mouse sensitivity.
# waitonerror -- Wait before closing the console if dosbox has an error.
fullscreen=true
fulldouble=false
fullfixed=false
fullwidth=0
fullheight=0
output=surface
hwscale=1.00
autolock=true
sensitivity=100
waitonerror=true
[dosbox]
# language -- Select another language file.
# memsize -- Amount of memory dosbox has in megabytes.
# machine -- The type of machine tries to emulate:hercules,cga,tandy,vga.
language=
machine=vga
memsize=16
[render]
# frameskip -- How many frames dosbox skips before drawing one.
# snapdir -- Directory where screenshots get saved.
# aspect -- Do aspect correction.
# scaler -- Scaler used to enlarge/enhance low resolution modes.
# Supported are none,normal2x,advmame2x,hq2x
# hq2x_threshold -- The threshold used to detect edges in hq2x
# Possible values are 4-128, can be modified with Ctrl+F3/F4
frameskip=0
snapdir=snaps
aspect=false
scaler=none
hq2x_threshold=18
[cpu]
# core -- CPU Core used in emulation: normal,full,dynamic.
# cycles -- Amount of instructions dosbox tries to emulate each millisecond.
# Setting this higher than your machine can handle is bad!
# cycleup -- Amount of cycles to increase/decrease with keycombo.
# cycledown Setting it lower than 100 will be a percentage.
core=dynamic
cycles=18000
cycleup=500
cycledown=500
[mixer]
# nosound -- Enable silent mode, sound is still emulated though.
# rate -- Mixer sample rate, setting any devices higher than this will
# probably lower their sound quality.
# blocksize -- Mixer block size, larger blocks might help sound stuttering
# but sound will also be more lagged.
# wavedir -- Directory where saved sound output goes when you use the
# sound record key-combination, check README file.
nosound=false
rate=22050
blocksize=2048
wavedir=waves
[midi]
# mpu401 -- Enable MPU-401 Emulation.
# device -- Device that will receive the MIDI data from MPU-401.
# This can be default,alsa,oss,win32,coreaudio,none.
# intelligent -- Operate in Intelligent mode.
# config -- Special configuration options for the device.
mpu401=true
intelligent=false
device=default
config=
[sblaster]
# type -- Type of sblaster to emulate:none,sb1,sb2,sbpro1,sbpro2,sb16.
# base,irq,dma,hdma -- The IO/IRQ/DMA/High DMA address of the soundblaster.
# mixer -- Allow the soundblaster mixer to modify the dosbox mixer.
# sbrate -- Sample rate of soundblaster emulation.
# oplmode -- Type of OPL emulation: auto,cms,opl2,dualopl2,opl3.
# On auto the mode is determined by sblaster type.
# oplrate -- Sample rate of OPL music emulation.
type=sb16
base=220
irq=7
dma=1
hdma=5
mixer=true
sbrate=22050
oplmode=auto
oplrate=22050
[gus]
# gus -- Enable the Gravis Ultrasound emulation.
# base,irq1,irq2,dma1,dma2 -- The IO/IRQ/DMA addresses of the
# Gravis Ultrasound. (Same IRQ's and DMA's are OK.)
# rate -- Sample rate of Ultrasound emulation.
# ultradir -- Path to Ultrasound directory. In this directory
# there should be a MIDI directory that contains
# the patch files for GUS playback. Patch sets used
# with Timidity should work fine.
gus=true
rate=22050
base=240
irq1=5
irq2=5
dma1=3
dma2=3
ultradir=C:\ULTRASND
[speaker]
# pcspeaker -- Enable PC-Speaker emulation.
# pcrate -- Sample rate of the PC-Speaker sound generation.
# tandy -- Enable Tandy 3-Voice emulation.
# tandyrate -- Sample rate of the Tandy 3-Voice generation.
# disney -- Enable Disney Sound Source emulation.
pcspeaker=true
pcrate=22050
tandy=true
tandyrate=22050
disney=true
[bios]
# Nothing to setup yet!
[dos]
# xms -- Enable XMS support.
# ems -- Enable EMS support.
xms=true
ems=true
[modem]
# modem -- Enable virtual modem emulation.
# comport -- COM Port modem is connected to.
# listenport -- TCP Port the momdem listens on for incoming connections.
modem=false
comport=2
listenport=23
[ipx]
# ipx -- Enable ipx over UDP/IP emulation.
ipx=true
[autoexec]
# Lines in this section will be run at startup
I don't knowKiller 11 wrote:BUT HOW THE HELL I CAN TURN IT ON!!!
In order to protect the visitors of this site,
TTO Full Conversion!
This post has been lol 1337 times.
you know your dos box short cut, rightclick! on the icon then click on find target, then double click on dosbox.conf and theres the configuration!
Ah forget it. I'll come back now.
OH NOES its an IRC quote!
<jonty>
<DaveWorley> ...
<DaveWorley> BOBO!?
<jonty> Booooooooooooooooooooooooooooooooobo!
<DaveWorley> BOO!
<jonty> Binga-dinga-bo-bo
<DaveWorley> D:
<Bobo> Heh, this is IRC quote material.
Small and compact quotes! Gotta love em.
OH NOES its an IRC quote!
<jonty>
<DaveWorley> ...
<DaveWorley> BOBO!?
<jonty> Booooooooooooooooooooooooooooooooobo!
<DaveWorley> BOO!
<jonty> Binga-dinga-bo-bo
<DaveWorley> D:
<Bobo> Heh, this is IRC quote material.
Small and compact quotes! Gotta love em.
I must admit dos box is a useful utility! I can run all My dos programs on it and it is the best
Ah forget it. I'll come back now.
OH NOES its an IRC quote!
<jonty>
<DaveWorley> ...
<DaveWorley> BOBO!?
<jonty> Booooooooooooooooooooooooooooooooobo!
<DaveWorley> BOO!
<jonty> Binga-dinga-bo-bo
<DaveWorley> D:
<Bobo> Heh, this is IRC quote material.
Small and compact quotes! Gotta love em.
OH NOES its an IRC quote!
<jonty>
<DaveWorley> ...
<DaveWorley> BOBO!?
<jonty> Booooooooooooooooooooooooooooooooobo!
<DaveWorley> BOO!
<jonty> Binga-dinga-bo-bo
<DaveWorley> D:
<Bobo> Heh, this is IRC quote material.
Small and compact quotes! Gotta love em.
If you are struggling with configuration, check out
http://members.home.nl/mabus/dfend.htm
Im using it and it works like a dream!
Its a pleasure!
http://members.home.nl/mabus/dfend.htm
Im using it and it works like a dream!
Its a pleasure!
DOS Box Configuration
I tried DosBox - and after three years I finally was able to see my beloved 1995-savegame again!
But still, I don't know how to configure Dosbox properly. With the recommended cycles-setting of 8,000 oder 9,000 the trains don't slide, they go step-by-step. When I increase the cycles to 20,000, the trains go nearly smoothly, but the music is being interrupted, and the game crashes after a while. And how about the memory? 32MB, 16MB? XMS and EMS??
Does anyone have a well running configuration for me?
I have a Pentium4 2,5GHz computer with 512MB RAM, ATI Radeon 9600TX, Soundblaster compatible...
But still, I don't know how to configure Dosbox properly. With the recommended cycles-setting of 8,000 oder 9,000 the trains don't slide, they go step-by-step. When I increase the cycles to 20,000, the trains go nearly smoothly, but the music is being interrupted, and the game crashes after a while. And how about the memory? 32MB, 16MB? XMS and EMS??
Does anyone have a well running configuration for me?
I have a Pentium4 2,5GHz computer with 512MB RAM, ATI Radeon 9600TX, Soundblaster compatible...
Re: DOS Box Configuration
I lost my best savegames *cry*Doclouis wrote: I tried DosBox - and after three years I finally was able to see my beloved 1995-savegame again!
DosBox.. Hmm, I think I've never been able to get the game running in it.
It would crash out immidiately
GoneWacko. Making [url=irc://irc.oftc.net/tycoon]#tycoon[/url] sexy and exciting since 1784.
I'm trying to get TTO to even install with DOSbox... not having any luck.
I have the very original version on 3.5 floppies... if I try to install the game in dosbox, it says I specified a drive that doesn't physically exist.
If I copy the 2 floppies to my C: drive, the first disk installs fine, but it can't seem to see the second disk.
Any ideas what I can do in order to install it?
I've read the dosbox readme, didn't see any special instructions for mounting the a: drive, but I'm wondering if there's a special flag I need to use.
Thanks!
I have the very original version on 3.5 floppies... if I try to install the game in dosbox, it says I specified a drive that doesn't physically exist.
If I copy the 2 floppies to my C: drive, the first disk installs fine, but it can't seem to see the second disk.
Any ideas what I can do in order to install it?
I've read the dosbox readme, didn't see any special instructions for mounting the a: drive, but I'm wondering if there's a special flag I need to use.
Thanks!
Im not sure why the second floppy isnt working but if it ever works you dont mount the floppy drive you mount the c drive and then change the directory like old dos to get to the TTO directory normally its cd\mps\trans then hit enter then trans again that should start
TTDX Nothin better...Nuff said!!...Need any other entertainment visit http://furdude2.proboards43.com/index.cgi an see if anyone has any of this interests as well.
I got a IRC channel too!! go to Quakenet then go to #furdude2
(Visit http://www.cafepress.com/leaveamessage for some fun items!!)
Visit http://myinterpagedesigninc.com/InterpageDesignINC.htm if you need a Site for a guild(any game will do) or a regular site. Visit http://sharecash.org/download.php?file=359761 to get my FAQ!
I got a IRC channel too!! go to Quakenet then go to #furdude2
(Visit http://www.cafepress.com/leaveamessage for some fun items!!)
Visit http://myinterpagedesigninc.com/InterpageDesignINC.htm if you need a Site for a guild(any game will do) or a regular site. Visit http://sharecash.org/download.php?file=359761 to get my FAQ!
to ascess drive C: type:
Code: Select all
mount c c:\ then press ENTER
cd (Installed folder) then press ENTER
tycoon then press ENTER
PLAY!
Face the fearful with no fear, and its fearfulness disappears.
- Redirect Left
- Tycoon
- Posts: 7270
- Joined: 22 Jan 2005 19:31
- Location: Wakefield, West Yorkshire
Yes, it doesn't really need that powerful computer. It even worked on my p333, well, loading a map took ages and the game was s l o w.
In order to protect the visitors of this site,
TTO Full Conversion!
This post has been lol 1337 times.
Who is online
Users browsing this forum: No registered users and 8 guests